532196853 Drive Belt - for Husqvarna Poulan Jonsered Dixon Walk-Behind Mowers - Replaces 196853 426609 532426609 590000501 583432701 | Aramid Cord | 32.38"
532196853 Drive Belt shown coiled with BlueStars packaging labeled lawn mower belt and 32.38in
532196853 Drive Belt, specs graphic showing 3/8in top width, 32.38in outer length, 0.222in bottom width and 0.22in height.
532196853 Drive Belt comparison graphic showing belt on mower pulleys with 120% grip claim versus a slipped or torn belt
532196853 Drive Belt in BlueStars packaging beside claims for 120-hour fatigue life and 2.64kN/m bonding strength
532196853 Drive Belt, infographic showing green belt and 3-layer material construction with aramid cords
532196853 Drive Belt compatibility chart with replacement part numbers and fit models, plus green belt
532196853 Drive Belt compatibility guide showing drive belt identification, parts label location, and mower compatibility ste
532196853 Drive Belt maintenance graphic with belt packaging and matching deck belt compatibility chart
532196853 Drive Belt infographic showing green belt beside a walk-behind mower and listed mowing symptoms
532196853 Drive Belt - installation guide graphic showing a walk-behind mower and green replacement belt
532196853 Drive Belt - pre-installation checklist graphic with green belt and tips for checking pulley bearings, edges, groov
532196853 Drive Belt shown coiled with BlueStars packaging labeled lawn mower belt and 32.38in
532196853 Drive Belt, specs graphic showing 3/8in top width, 32.38in outer length, 0.222in bottom width and 0.22in height.
532196853 Drive Belt comparison graphic showing belt on mower pulleys with 120% grip claim versus a slipped or torn belt
532196853 Drive Belt in BlueStars packaging beside claims for 120-hour fatigue life and 2.64kN/m bonding strength
532196853 Drive Belt, infographic showing green belt and 3-layer material construction with aramid cords
532196853 Drive Belt compatibility chart with replacement part numbers and fit models, plus green belt
532196853 Drive Belt compatibility guide showing drive belt identification, parts label location, and mower compatibility ste
532196853 Drive Belt maintenance graphic with belt packaging and matching deck belt compatibility chart
532196853 Drive Belt infographic showing green belt beside a walk-behind mower and listed mowing symptoms
532196853 Drive Belt - installation guide graphic showing a walk-behind mower and green replacement belt
532196853 Drive Belt - pre-installation checklist graphic with green belt and tips for checking pulley bearings, edges, groov
Lifetime Warranty

532196853 Drive Belt - for Husqvarna Poulan Jonsered Dixon Walk-Behind Mowers - Replaces 196853 426609 532426609 590000501 583432701 | Aramid Cord | 32.38"

Save 10%
0.00
$9.36
$10.39
$9.36
In stock
Fast delivery

Secure and trusted checkout with

  • Visa
  • Mastercard
  • American Express
  • PayPal
  • Diners Club
  • Discover
Contact for wholesale
πŸ› οΈ
CONFIRM THE FIT FOR YOUR MODEL
Enter your model number

532196853 Drive Belt for Walk-Behind Mowers

Key Features

  • Drive belt for transferring engine power to the mower pulleys and helping propel the mower forward or backward.
  • Aramid cord construction with a covered belt design.
  • Green finish; one belt included.
  • Outer length: 32.38 inches.
  • Top width: 3/8 inch; bottom width: 0.222 inch; height: 0.22 inch.
  • Fabric-wrapped construction supports grip and stable power transmission during operation.

Replaces

This belt replaces the following mower drive belt numbers:

  • Husqvarna 532196853
  • 196853
  • 583432701
  • 590000501
  • Craftsman 426609
  • 532426609

Cross-Reference Part Numbers

  • 532196853
  • 196853
  • 426609
  • 532426609
  • 590000501
  • 583432701

Compatibility & Fitment

Compatible with selected Husqvarna, Craftsman, Poulan, Poulan Pro, Jonsered, Dixon, and MTD walk-behind mower models. Confirm the belt dimensions and your mower model before ordering.

  • Husqvarna: 5521 CHV (961430001-03, 961430001-04, 961430001-05), 65021 CHV (961430019-00), HU550F, HU550FH, HU725F, HU725FH, LB155S, J55SL (961210018-07, 961210018-08)
  • Craftsman: 700 Series Platinum, 917.375452, 917.377550, 944.362080
  • Poulan / Poulan Pro: PR625P, PR625Y22RHP, PR625Y22RP, PR675Y22RHP, PR675Y22RHPE, PR725Y22RHP, 961420116-01, 961420116-02, 961420116-03, 961420117-01, 961420117-02, 961480049-00, 961480049-01, 961480050-00, 961490002-01, 961490002-02, 961420133-00
  • Jonsered: LM2153CMDAW, LM2156CMDA, LM2155MD (961210019-05, 961210019-06, 961210036-00), J160FH22
  • Dixon: D149F22
  • MTD: 25B-551A729

The model list is not exhaustive. Use the mower model and belt measurements to verify fitment.

When to Replace

Replace the drive belt when it no longer transfers power reliably or shows visible damage. Common replacement signs include:

  • Cracks or significant wear
  • A rolled or turned-over belt
  • Damage along the side wall
  • A burned, glazed, or shiny side wall
  • Reduced drive engagement, slipping, or inconsistent mower movement

Restricted pulleys, incorrect belt routing, or worn pulley components can also cause premature belt wear. Inspect the complete drive system when installing a new belt.

Installation Tips

  • Stop the engine, disconnect the spark-plug wire, and allow the mower to cool before servicing the belt.
  • Block or position the mower securely according to the equipment manufacturer’s service procedure.
  • Photograph or note the original belt routing before removal.
  • Inspect the pulleys, belt guides, and tensioning components for debris, sharp edges, looseness, or wear.
  • Install the belt in the original routing without twisting it, then confirm that it sits correctly in each pulley groove.
  • Rotate the drive system by hand, where safe and practical, to verify alignment before reconnecting the spark-plug wire.
  • Allow approximately 30–60 minutes for installation, depending on mower design and access to the drive system.
Product image
Product image
Product image 1
Product image 2
  • PART NUMBERS

    PART NUMBERS

    This Drive Belt replaces: Husqvarna 532196853, 196853, 583432701, 590000501; Craftsman 426609, 532426609; Poulan 532426609
  • SAVING SOLUTION

    SAVING SOLUTION

    Enjoy the great feeling when your mower is repaired and works like before - BlueStars brings DIY solutions to help you deal with any trouble
  • FIX MOWER'S SYMPTOMS

    FIX MOWER'S SYMPTOMS

    Slipping or Inconsistent Speed, Loud or Unusual Noises, Excessive Vibration, Burning Smell, Moves slowly or Fails to move
  • IMPORTANT NOTE

    IMPORTANT NOTE

    This is a replacement part designed to be compatible with certain appliances. Any brand names mentioned are used solely to indicate compatibility.
CHECK BEFORE INSTALLING

CHECK BEFORE INSTALLING

- Pulley Bearings: Make sure they spin freely, as damaged bearings can increase friction and wear
- Pulleys Edges: Rust or sharp edges can cause belt damage
- Pulley Grooves: Clean debris from the pulley grooves
- Tensioner Spring: A weak spring can lead to belt slippage and increased friction
4 SIMPLE STEPS

4 SIMPLE STEPS

- Remove the ignition key and spark plug wire(s). Let the engine cool.
- Remove the mower deck.
- Release the old drive belt from the pulleys. (Take a photo of the belt routing first.)
- Install the new belt and check for proper operation.
Brand Model Number
Husqvarna 5521 CHV (961430001-03, -04, -05), 65021 CHV (961430019-00), HU550F, HU550FH, HU725F, HU725FH, LB155S, J55SL (961210018-07, -08)
Jonsered LM2153CMDAW, LM2156CMDA, LM2155MD (961210019-05, -06; 961210036-00), J160FH22
Poulan PR625P, PR625Y22RHP, PR625Y22RP, PR675Y22RHP, PR675Y22RHPE, PR725Y22RHP, 961420116-01 to 03, 961420117-01 to 02, 961480049-00 to 01, 961480050-00, 961490002-01 to 02, 961420133-00
Dixon D149F22
Craftsman 917.375452, 917.377550, 944.362080
MTD 25B-551A729

FAQ

This drive belt is intended for compatible Husqvarna, Poulan, Jonsered, and Dixon walk-behind lawn mowers. Confirm the mower’s existing belt number and routing before ordering, since fitment can vary by model.
It replaces 196853, 426609, 532426609, 590000501, and 583432701. The specified belt length is 32.38 inches and it uses aramid cord construction.
Common signs include the mower failing to move, slipping or jerking during operation, reduced drive speed, squealing, visible fraying or cracking, and a belt that has stretched or broken. A damaged pulley or an obstructed drive system can cause similar symptoms.
Installation is generally a moderate repair and often takes about 30–60 minutes, depending on the mower design. Typical tools include socket or wrench set, screwdrivers, pliers, and a suitable block or work support. Disconnect the spark plug wire before working near the belt and follow the original belt-routing path carefully.
Inspect the drive pulleys, belt guides, tensioner, and mower deck or transmission area for bent parts, seized bearings, grass buildup, or debris. Clean the pulley grooves and verify that the replacement belt is routed correctly and is not twisted before reassembly.